Configuratore roll bar solare

Progetta il tuo roll bar solare e scopri il prezzo

Scegli un modello, aggiungi le opzioni che servono alla tua barca e guarda il prezzo aggiornarsi. Ruota il modello con il dito o con il mouse. I prezzi sono IVA esclusa e confermiamo il prezzo finale dopo aver verificato le tue misure.

Per ora il configuratore è in inglese.

Quattro passi per il tuo preventivo

  1. 1Progetta
  2. 2I tuoi dati
  3. 3Controlla il preventivo
  4. 4Invia

Design

A smaller welded arch with clean lines, for up to 3 medium panels. Ideal for boats up to 45 ft.

More about Eiviva

Eiviva is a fully welded one-piece arch with clean lines. Each side is made in one plane and the top crosses straight between them. Two 1" cross members sit at the same height as the pushpit rails, and one more sits just below the top bend. Joined to the pushpit, it stands on the pushpit's own deck fittings, so the deck needs no new holes. Cables run inside the tubes and go into the boat through hollow base plates.

Height
Up to 1.8 m
Width
2 to 3.2 m
Feet apart, front to back
450 to 750 mm
Tube
38 mm, mirror polished 316 stainless steel
Panels
Up to 3 medium panels, about 250 W each
Weight
30 to 50 kg
Suits
Ideally boats up to 45 ft
An Eiviva arch on a boatAn Eiviva arch on a boat

Width

The standard Eiviva is 3.0 m wide. A wider arch suits a wider boat. Each extra 0.5 m adds 7% to the price of the arch. Your arch: 3.0 m.

Shape of the top

The top tubes of the front and rear frames, and the top of the U-shaped davit, run straight across. This is quicker to make, so it costs less.

More about this top

On the straight top, the top tube of each frame runs straight across between the two top bends. The side frames, panels and fittings are the same as on the curved top. Straight tube is quicker to cut, bend and weld, so this is the lower cost choice.

Photos to come

How it is fitted

The arch stands on its own feet, and the boat keeps its own pushpit around it. The U-shaped davit cannot be fitted, because the pushpit behind the arch is in the way when it lowers.

More about this fitting

A freestanding arch has its own feet on the deck, inside the boat's pushpit. The pushpit stays as it is. The U-shaped davit needs the space behind the arch to swing down to the water, so it only goes with an arch joined to the pushpit. Lifting eyes and tubular davits work with both.

A freestanding arch inside the boat's pushpit

Solar panels

Panels sit side by side across the top, overhanging the frame slightly at the front and back. Their size is chosen to suit your boat.

More about the panels

Each panel is held on round bar struts. A plate on top of each strut takes the panel and is fixed with one M8 bolt, so panels can be changed later. The cables run inside the arch tubes into the boat.

Solar panels on the arch fittingsSolar panels on the arch fittings

Dinghy davits

The U-shaped davit needs the arch joined to the pushpit. With a freestanding arch, the boat's own pushpit is in the way of the davit as it swings down. Choose “Joined to pushpit” above to fit it.

No davit. Davits can be added later.

More about this davit

A davit can be added later.

Photos to come

Equipment

Aerial bracket

A fork bracket for VHF and AIS aerials and a GPS antenna, on the side of the arch.

More about this

The bracket can take as many aerials and GPS antennas as you need. The cables run inside the arch.

An aerial bracket on the archAn aerial bracket on the archAn aerial bracket on the arch
Starlink bracket

A post on the side of the arch with a plate that lifts the dish above the panels.

More about this

The plate lifts the dish just above the panels, clear of the frame.

A Starlink bracket on the arch
Radar dome bracket

A post on the side of the arch with a plate for the radar dome.

More about this

The plate lifts the radar dome just above the panels, clear of the frame.

A radar dome bracket on the archA radar dome bracket on the arch
Wind generator pole

A tall pole on the side of the arch, high enough to keep the blades clear of the crew and the panels.

More about this

The pole is set so the blade tips pass about 100 mm above the panels.

A wind generator on the archA wind generator on the arch
Flag pole holder

A short socket clamped to the lower stern rail of the pushpit holds the ensign staff.

More about this

A short stainless socket is clamped to the lower stern rail of the pushpit, near the corner. The ensign staff drops into it and leans out over the stern, and lifts out when you want it stowed.

An ensign on the stern
Liferaft cradle

A separate tube cradle clamped to the back of the stern rails, so the liferaft hangs out over the water. A quick release lets the liferaft float free if the boat sinks. It cannot be fitted together with the pushpit seats.

More about this

The cradle is a separate unit made of two 1" frames, one in front of the liferaft and one behind it, joined by one tube all round. Tube clamps hold it to the stern rails. A strap over the liferaft runs to a quick release unit.

A liferaft cradle on the pushpitA liferaft cradle on the pushpit
Pushpit seats

Teak corner seats built into the stern rails. The front of each seat sits over the transom edge and the seat reaches out behind the boat. They cannot be fitted together with the liferaft cradle.

More about this

The seat frame carries on from the lower stern rail, and the top stern rail goes round the back of the seat as the backrest. One strut under each seat runs down to the deck.

Pushpit seatsPushpit seats
Extended safety rails

Steel rails run forward from the arch on both sides, in place of the guard wires. About 1.5 m to the first stanchion, or about 3 m to the stanchion gate.

More about this

Rails to the first stanchion are about 1.5 m long. Rails to the stanchion gate are about 3 m long.

Extended safety railsExtended safety rails

Installation

We make the arch and you, or your boatyard, fit it. Packing and delivery are quoted once we know where it is going.

Your setup

  • Eiviva arch£4800
  • 3.0 m wide (standard)Included
  • Straight topIncluded
  • FreestandingIncluded
  • Fittings for 2 solar panelsIncluded
  • Supply only, no installationNo charge

£4800+ VAT

Estimate. Final price confirmed after we check your measurements.

Supply only: you or your boatyard fit the arch. Would you like us to fit it further than 25 miles away? That is £960 + VAT a day for two fitters, plus travel and expenses.

Packing and delivery are quoted once we know where it is going. Outside the UK? Import VAT and duty are paid on arrival.

★★★★★
The guys were amazing all through the design and manufacture of the arch made for my Najad 490. The quality was fantastic and proved a valuable addition to the yacht. They consulted me at every stage and made sure I was happy with everything at every stage. Very skilled people at what they do.
Andrew, Najad 490 "Lahaina", Valkyrie arch
★★★★★
Great service! Built us a beautiful arch with davits in 2 weeks, on budget. Very professional and good communication throughout. Highly recommend.
Rob, Moody 40, Valkyrie arch

Rated 5 stars on Google

Green Innovator Award Winner

A question to ask any fabricatorHow many arches have you built? We have fitted more than 290.

Step 1 of 4. Sending a request is free. We check every design and send you a formal quote.

The Eiviva, Valkyrie, Dodger and Universal designs belong to Latbros Ltd.

Installazioni reali

Guarda i roll bar che abbiamo costruito

Ogni modello del configuratore nasce da roll bar montati su barche vere. Guarda il lavoro finito, con foto e recensioni degli armatori, prima di inviare la richiesta.

Utilizziamo i cookie per capire come i visitatori usano il nostro sito.